HPE7-A01 Dumps PDF 2026 Strategy Your Preparation Efficiently

Latest Verified & Correct HP HPE7-A01 Questions

HPE7-A01 exam covers a wide range of topics such as Aruba WLAN fundamentals, Aruba OS 8.x features and functionality, and Aruba Mobility Master and Mobility Controller architecture. It also covers topics such as Aruba access points, RF fundamentals, and the implementation of Aruba wireless solutions in enterprise environments.

 

NEW QUESTION # 93
Your Director of Security asks you to assign AOS-CX switch management roles to new employees based on their specific job requirements After the configuration was complete, it was noted that a user assigned with the administrators role did not have the appropriate level of access on the switch.
The user was not limited to viewing nonsensitive configuration information and a level of 1 was not assigned to their role Which default management role should have been assigned for the user?

• A. helpdesk
• B. operators
• C. sysadmin
• D. config

Answer: A

Explanation:
Explanation
The helpdesk role is the default management role that should have been assigned for the user who needs to view nonsensitive configuration information. The helpdesk role has a level of 1 and allows read-only access to most commands except those related to security or passwords. The administrators role has a level of 15 and allows full read-write access to all commands. The operators role has a level of 5 and allows read-write access to most commands except those related to security or passwords. The config role has a level of 10 and allows read-write access to all commands except those related to security or passwords. References:
https://www.arubanetworks.com/techdocs/AOS-CX_10_08/UG/bk01-ch01.html
https://www.arubanetworks.com/techdocs/AOS-CX_10_08/UG/bk01-ch04.html

NEW QUESTION # 94
Match the solution components of HPE Aruba Networking Central NetConductor (Options may be used more than once or not at all.)

Answer:

Explanation:

Explanation:

NEW QUESTION # 95
A company deployed Dynamic Segmentation with their CX switches and gateways. After performing a security audit on their network discovered that the tunnels built between the CX switch and the HPE Aruba Networking gateway are not encrypted. The company is concerned that bad actors could try to insert spoofed messages on the gateway to disrupt communications or obtain information about the network.
Which action must the administrator perform to address this situation?

• A. Enable Secure Mode Enhanced
• B. Enable Enhanced PAPI security
• C. Enable Enhanced security
• D. Enable GRE security

Answer: B

Explanation:
PAPI is the protocol that is used to establish tunnels between the CX switch and the Aruba Gateway for Dynamic Segmentation. By default, PAPI uses a simple checksum to verify the integrity of the messages, but it does not encrypt the payload. This could expose the network to spoofing or replay attacks by malicious actors. To address this situation, the administrator must enable Enhanced PAPI security, which uses AES-256 encryption and HMAC-SHA1 authentication to protect the tunnel traffic. Enhanced PAPI security can be enabled on the CX switch by using the command system papi enhanced-security enable. This will ensure that the tunnels built between the CX switch and the Aruba Gateway are encrypted and authenticated.

NEW QUESTION # 96
Due to a shipping error, five (5) Aruba AP-515S and one (1) Aruba CX 6300 were sent directly to your new branch office. You have configured a new group persona for the new branch office devices in Central, but you do not know their MAC addresses or serial numbers. The office manager is instructed via text message on their smartphone to onboard all the new hardware into Aruba Central.
What application must the office manager use on their phone to complete this task?

• A. Aruba Onboard App
• B. Aruba Central App
• C. Aruba installer App
• D. Aruba CX Mobile App

Answer: B

Explanation:
Aruba Central is a cloud-based networking solution that empowers IT with AI-powered insights, intuitive visualizations, workflow automation, and edge-to-cloud security to manage campus, branch, remote, data center, and IoT networks from one dashboard. Aruba Central also provides a mobile app that allows users to easily onboard and monitor devices. The app enables users to scan the barcode of a device (such as an AP or a switch) and add it to their network in Aruba Central. The app also lets users monitor the details of Aruba wireless access points and switches and their clients on their network. Therefore, the application that the office manager must use on their phone to complete the task of onboarding all the new hardware into Aruba Central is the Aruba Central App.

NEW QUESTION # 97
Drag and Drop Question
Match the topics of an AOS10 Tunneled mode setup between an AP and a Gateway. (Options may be used more than once or not at all.)

Answer:

Explanation:

NEW QUESTION # 98
Your Director of Security asks you to assign AOS-CX switch management roles to new employees based on their specific job requirements. After the configuration was complete, it was noted that a user assigned with the auditors role did not have the appropriate level of access on the switch.
The user was not allowed to perform firmware upgrades and a privilege level of 15 was not assigned to their role. Which default management role should have been assigned for the user?

• A. sysadmin
• B. administrators
• C. sysops
• D. config

Answer: B

Explanation:
https://www.arubanetworks.com/techdocs/AOS-CX/10.07/HTML/5200-7885/Content/Chp_Mng_Use/bui-in- use-gro-the-pri-10.htm

NEW QUESTION # 99
Drag and Drop Question
Select the Aruba stacking technology matching each option (Options may be used more than once or not at all.)

Answer:

Explanation:

NEW QUESTION # 100
A system engineer needs to preconfigure several Aruba CX 6300 switches that will be sent to a remote office An untrained local field technician will do the rollout of the switches and the mounting of several AP-515s and AP-575S. Cables running to theAPs are not labeled.
The VLANs are already preconfigured to VLAN 100 (mgmt), VLAN 200 (clients), and VLAN 300 (guests) What is the correct configuration to ensure that APs will work properly?

• A.
• B. e ip="img_94.jpg"></e>
• C.
• D.

Answer: D

Explanation:
Explanation
Option C is the correct configuration to ensure that APs will work properly. It uses the ap command to configure a port profile for APs with VLAN 100 as the native VLAN and VLAN 200 and 300 as tagged VLANs. It also enables LLDP on the ports to discover the APs and assign them to the port profile automatically. The other options are incorrect because they either do not use the ap command, do not enable LLDP, or do not configure the VLANs correctly. References:
https://www.arubanetworks.com/techdocs/AOS-CX_10_08/UG/bk01-ch02.html
https://www.arubanetworks.com/techdocs/AOS-CX_10_08/UG/bk01-ch03.html

NEW QUESTION # 101
You are configuring an SVI on an Aruba CX switch that needs to have the following characteristics:
* VLANID = 25
. IPv4 address 10 105 43 1 with mask 255 255 255.0
* IPv6 address fd00:5708::f02d:4df6 with a 64 bit prefix length
* member of VRF eng
* VRF eng and VLAN 25 have not yet been created
Which command lists will satisfy the requirements with the least number of commands?

• A.
• B.
• C.
• D.

Answer: D

NEW QUESTION # 102
Your customer is interested in hearing more about how roles can help keep consistent policy enforcement in a distributed overlay fabric How would you explain this concept to them''

• A. Group Based Policy ID is applied on egress VTEP after device authentication and policy is enforced on ingress VTEP
• B. Group Based Policy ID is applied on ingress VTEP after device authentication and policy is enforced on egress VTEP
• C. Role-based policies enhance User Based Tunneling across the campus network and the policy traffic is protected with iPsec
• D. Role-based policies are tied to IP addresses which have an advantage over IP-based policies and role names are sent between VTEPs

Answer: B

Explanation:
This is the correct explanation of how roles can help keep consistent policy enforcement in a distributed overlay fabric. Roles are used to assign group based policy IDs (GBPs) to devices after they authenticate with ClearPass or a local database. GBPs are then used to tag the traffic from the devices and send them to the ingress VTEP, which applies the GBP on the VXLAN header. The egress VTEP then enforces the policy based on the GBP and the destination device. The other options are incorrect because they either do not describe the correct sequence of events or do not use the correct terms. References:
https://www.arubanetworks.com/techdocs/AOS-CX/10.04/HTML/5200-6728/bk01-ch03.htmlhttps://www.aruba

NEW QUESTION # 103
What is one advantage of using OCSP vs CRLs for certificate validation?

• A. supports longer certificate validity periods
• B. less complex to implement
• C. higher availability for certificate validation
• D. reduces latency between the time a certificate is revoked and validation reflects this status

Answer: D

Explanation:
OCSP is a protocol that allows clients to query the CA or a trusted responder for the status of a specific certificate. OCSP requests and responses are smaller and faster than CRLs, and they can provide real-time information about the revocation status of a certificate12. CRLs are lists of all revoked certificates that are downloaded from the CA. CRLs can present issues, as they can become outdated and have to be downloaded frequently13. Therefore, OCSP reduces latency between the time a certificate is revoked and validation reflects this status. References: 1 https://sectigostore.com/blog/ocsp-vs-crl-whats-the-difference/ 2
https://www.keyfactor.com/blog/what-is-a-certificate-revocation-list-crl-vs-ocsp/ 3
https://www.fortinet.com/resources/cyberglossary/ocsp

NEW QUESTION # 104
With Aruba CX 6300. how do you configure ip address 10 10 10 1 for the interface in default state for interface 1/1/1?

• A. int 1/1/1. switching, ip address 10 10 10 1/24
• B. int 1/1/1. no switching, ip address 10 10 10.1/24
• C. int 1/1/1. routing, ip address 10.10.10 1/24
• D. int 1/1/1. ip address 10.10.10.1/24

Answer: B

Explanation:
To configure an IP address for an interface in default state for interface 1/1/1 on Aruba CX 6300 switch, you need to disable switching on the interface first with the command no switching. Then you can assign an IP address with the command ip address. The other options are incorrect because they either do not disable switching or use invalid keywords such as switching or routing.
References:
https://www.arubanetworks.com/techdocs/AOS-CX_10_08/UG/bk01-ch01.html
https://www.arubanetworks.com/techdocs/AOS-CX_10_08/UG/bk01-ch02.html

NEW QUESTION # 105
Refer to the image.

Your customer is complaining of weak Wi-Fi coverage in their office. They mention that the office on the other side of the hall has much better signal What is the likely cause of this issue7

• A. The AP is using a directional antenna.
• B. The AP is a remote access point.
• C. The AP is configured in Mesh mode
• D. The AP is an outdoor access point.

Answer: A

Explanation:
Explanation
The likely cause of the issue of weak Wi-Fi coverage in the office is that the AP is using a directional antenna.
A directional antenna is an antenna that radiates or receives radio waves more strongly in one or more directions, creating a focused beam of signal. A directional antenna can provide better coverage and performance for a specific area, but it can also create dead zones or weak spots for other areas. The other options are incorrect because they either do not affect the Wi-Fi coverage or do not match the scenario.
References:
https://www.arubanetworks.com/techdocs/ArubaOS_86_Web_Help/Content/arubaos-solutions/wlan-rf/rf-fundam
https://www.arubanetworks.com/techdocs/ArubaOS_86_Web_Help/Content/arubaos-solutions/wlan-rf/antennas.

NEW QUESTION # 106
A customer wants to deploy a Gateway and take advantage of all the SD-WAN features. Which persona role option should be selected?

• A. ArubaOS 10 VPN Concentrator
• B. ArubaOS 10 Branch
• C. ArubaOS 10 Mobility
• D. ArubaOS 10 Wireless

Answer: B

Explanation:
The persona role option that should be selected to deploy a Gateway and take advantage of all the SD-WAN features is A. ArubaOS 10 Branch.
ArubaOS 10 Branch is a persona that enables the Gateway to provide both LAN and WAN functionality for branch networks. The Gateway can act as a wireless controller, a router, a firewall, and an SD-WAN device. The SD-WAN features include route and tunnel orchestration, dynamic path steering, forward error correction, SaaS traffic optimization, SASE orchestration, and more1.
The other options are incorrect because:
B) ArubaOS 10 VPN Concentrator: This is a persona that enables the Gateway to act as a VPN concentrator for remote access or site-to-site VPN connections. It does not provide SD-WAN features2.
C) ArubaOS 10 Wireless: This is a persona that enables the Gateway to act as a wireless controller for campus networks. It does not provide SD-WAN features3.
D) ArubaOS 10 Mobility: This is a persona that enables the Gateway to act as a mobility controller for campus networks. It does not provide SD-WAN features.

NEW QUESTION # 107
Which statements are true regarding a VXLAN Implementation on HPE Aruba Networking switches? (Select two.)

• A. MTU size must be increased beyond the default.
• B. They are only available for datacenter switches (CX 8k, 9k, 10k).
• C. VTEPs encapsulate and decapsulate VXLAN traffic.
• D. All AOS-CX switches support VXLAN.
• E. VNIs encapsulate and decapsulate VXLAN traffic.

Answer: A,C

NEW QUESTION # 108
You must ensure the HPEAruba network you are configuring for a client is capable of plug-and-play provisioning of access points. What enables this capability?

• A. UCC Service
• B. LLDP-MED
• C. CSMA
• D. SRTP

Answer: A

Explanation:
The capability that enables plug-and-play provisioning of access points in an HPE Aruba network is the UCC Service. The UCC Service is a cloud-based service that allows the access points to automatically discover and connect to the Aruba Central management platform without any manual intervention. The UCC Service also provides zero-touch configuration, firmware updates, and monitoring for the access points1.
The other options are incorrect because:
B) LLDP-MED: LLDP-MED is a protocol that enhances the interoperability between network devices and IP phones. It does not enable plug-and-play provisioning of access points2.
C) SRTP: SRTP is a protocol that provides encryption and authentication for voice and video traffic. It does not enable plug-and-play provisioning of access points3.
D) CSMA: CSMA is a protocol that regulates how devices share a common medium, such as a wireless channel. It does not enable plug-and-play provisioning of access points.

NEW QUESTION # 109
You are deploying a bonded 40 MHz wide channel.
What is the difference in the noise floor perceived by a client using this bonded channel as compared to an unbonded 20MHz wide channel?

• A. 3dB
• B. 4dB
• C. 2dB
• D. 8dB

Answer: A

Explanation:
The difference in the noise floor perceived by a client using a bonded 40 MHz wide channel as compared to an unbonded 20 MHz wide channel is 3 dB. The noise floor is the level of background noise in a given frequency band. When two adjacent channels are bonded, the noise floor increases by 3 dB because the bandwidth is doubled and more noise is captured. The other options are incorrect because they do not reflect the correct relationship between bandwidth and noise floor.
References:
https://www.arubanetworks.com/techdocs/ArubaOS_86_Web_Help/Content/arubaos-solutions/wlan-rf/rf- fundam
https://www.arubanetworks.com/techdocs/ArubaOS_86_Web_Help/Content/arubaos-solutions/wlan- rf/channel-b

NEW QUESTION # 110
You are configuring an SVI on an Aruba CX switch that needs to have the following characteristics:
* VLANID = 25
. IPv4 address 10 105 43 1 with mask 255 255 255.0
* IPv6 address fd00:5708::f02d:4df6 with a 64 bit prefix length
* member of VRF eng
* VRF eng and VLAN 25 have not yet been created
Which command lists will satisfy the requirements with the least number of commands?

• A.
• B.
• C.
• D.

Answer: B

Explanation:
The other options either use more commands or do not create the VRF or the VLAN.
Option C uses the following commands:
* vrf eng: This command creates a VRF named eng and enters the VRF configuration mode1.
* vlan 25: This command creates a VLAN with ID 25 and enters the VLAN configuration mode2.
* interface vlan 25: This command creates an SVI on VLAN 25 and enters the interface configuration mode3.
* ip address 10.105.43.1/24 ipv6 address fd00:5780::102d:4df6/64 vrf attach eng: This command assigns an IPv4 address of 10.105.43.1 with a subnet mask of 255.255.255.0 and an IPv6 address of fd00:5780::
102d:4df6 with a prefix length of 64 to the SVI, and attaches it to the VRF eng.

NEW QUESTION # 111
When setting up an Aruba CX VSX pair, which information does the Inter-Switch Link Protocol configuration use in the configuration created?

• A. QSVI
• B. RPVST+
• C. MAC tables
• D. UDLD

Answer: D

Explanation:
UDLD (Unidirectional Link Detection) is the information that the Inter-Switch Link Protocol configuration uses in the configuration created for Aruba CX VSX pair inter-switch-link. UDLD is a protocol that detects unidirectional links between switches and prevents loops or black holes in the network. UDLD is enabled by default on all ports that are part of the inter-switch-link between VSX peers. The other options are incorrect because they are either not related to inter-switch-link or not supported by Aruba CX VSX.

NEW QUESTION # 112
......

HP HPE7-A01 exam is an essential certification program for professionals seeking to enhance their skills in designing and deploying wireless networks. HPE7-A01 exam covers a wide range of topics, and the certification program offers a comprehensive curriculum that prepares candidates for different scenarios and challenges. Passing the exam and obtaining the Aruba Certified Access Professional (ACCP) certification will enhance the career prospects of networking professionals and demonstrate their expertise in wireless network design and deployment.

HP HPE7-A01 (Aruba Certified Campus Access Professional) certification exam is an essential certification for IT professionals who specialize in wireless networking and network design. Aruba Certified Campus Access Professional Exam certification exam tests the knowledge and skills required to design, configure, and troubleshoot wireless networks in modern campus environments. Candidates who pass the HPE7-A01 certification exam will have the knowledge and skills to design and manage wireless networks that meet the needs of today's businesses and organizations.

 

HPE7-A01 PDF Dumps Are Helpful To produce Your Dreams Correct QA's: https://pass4sure.examstorrent.com/HPE7-A01-exam-dumps-torrent.html