Get 350-501 Products Practice Material for 350-501 Exam Question Preparation
Most Reliable Cisco 350-501 Training Materials
Cisco 350-501 exam covers various topics, including network architecture, automation, virtualization, security, and quality of service. 350-501 exam is designed to test the candidate's understanding of the fundamental concepts and technologies used in service provider network solutions.
NEW QUESTION # 94
Refer to the exhibit.
A network engineer is implementing an OSPF configuration. What is the output of this implementation?
- A. OSPFv3 cannot be configured for IPv4. OSPFv3 works only for IPv6.
- B. In the ospfv3 1 area 1 ipv4 command, area 0 must be configured instead of area 1.
- C. IPv6 routing not enabled' Is just an Informational message and OSPFv3 runs for IPv4 on interface FastEihernet0/0 anyway.
- D. OSPFv3 does not run for IPv4 on FastEthernetO'O until IPv61 routing is enabled on the router and IPv6 Is enabled on interface FastEthernet0/0.
Answer: D
NEW QUESTION # 95
Refer to the exhibit. What does this REST API script configure?
- A. VRF
- B. public community string for SNMP
- C. application profile
- D. interface with IP address 192.168.0.1
Answer: D
Explanation:
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/aci/apic/white_papers/Cisco-ACI- Initial-Deployment-Cookbook.html#_Toc6840570
NEW QUESTION # 96
Refer to the exhibit. This output is included at the end of an output that was provided by a device using NETCONF.
What does the code show?
- A. It shows NETCONF uses remote procedure calls.
- B. It shows that the full configuration is being modeled by VANG
- C. It shows the hostname of the device as rpc-reply
- D. It shows that the running configuration is blank
Answer: A
NEW QUESTION # 97
Refer to the exhibit:
A network engineer is implementing a BGP protocol. Which effect of the local-as keyword in this configuration is true?
- A. It enables peer 192.168.1.2 to establish a BGP relationship with R1 using AS 65112 without additional configuration.
- B. It enables peer 192.168.1.2 to establish a BGP relationship with R1 using AS 65012 without additional configuration
- C. It enables peer 192.168.1.2 to establish a BGP relationship with R1 using AS 65012 and the VPNv4 address family
- D. It enables peer 192.168.1.2 to establish a BGP relationship with R1 using AS 65112 and the VPNv4 address family
Answer: A
NEW QUESTION # 98
Why do Cisco MPLS TE tunnels require a link-state routing protocol'?
- A. The link state database provides segmentation by area, which improves the path-selection process
- B. Link-state routing protocols use SPF calculations that the tunnel endpoints leverage to implement the tunnel
- C. The tunnel endpoints can use the link-state database to evaluate the entire topology and determine the best path
- D. The link-state database provides a data repository from which the tunnel endpoints can dynamically select a source ID
Answer: C
NEW QUESTION # 99
Refer to the exhibit:
You are configuring an administrative domain implement so that devices can dynamically learn the RP?
- A. BID1R-PIM
- B. SSM
- C. BSR
- D. Auto-RP
Answer: C
NEW QUESTION # 100
Refer to the exhibit. The USER mat is connecting an application on an Internet connection in AS
100 is facing these issues:
The USER lost the connection to the application during a failure Between IG and R2. Router R2 configuration a lost due to a power outage. The application the USER is connecting to a hosted behind CE2. What action resolves the issues on R3 and R4 routers?
- A. Set R4 as a route reflector for R3 and CE2
- B. Apply low Local Preference on R4 toward R2.
- C. Apply high Local Preference on R3 toward R1
- D. Set R3 as a route reflector for R4 and CE1
Answer: B
NEW QUESTION # 101
While implementing TTL security, you issue the PE(config-router-af)#neighbor 2.2.2.2 ttl-security hops 2 command.
After you issue this command, which BGP packets does the PE accept?
- A. to 2.2.2.2, with a TTL of less than 253
- B. to 2.2.2.2, with a TTL of 2 or more
- C. from 2.2.2.2, with a TTL ol 253 Of more
- D. from 2.2.2.2, with a TTL of less than 2
Answer: D
NEW QUESTION # 102
Refer to the exhibit. An organization s network recently experienced several significant outages due to device failures. The network administrator just moved the network devices to a new central data center, and packets are switched using labels. The administrator Is now implementing NSF on the network to reduce potential risk factors in the event of another outage. Which task must the administrator perform on each router as part of the process?
- A. Remove route filtering to speed repopulation of the link-state database
- B. Implement Graceful Restart to mitigate the delay in MPLS LDP synchronization when the IGP starts up.
- C. Implement MPLS to forward packets while the RIB updates after a faliover.
- D. Copy the router s existing state information and share the file with its peers to enable BGP soft resets
Answer: B
NEW QUESTION # 103
Refer to the exhibit:
An engineer wants to authenticate the OSPF neighbor between PEA and PE-B using MD5.
Which command on PE-B successfully completes the configuration?
A)
B)
C)
D)
- A. Option A
- B. Option B
- C. Option D
- D. Option C
Answer: A
NEW QUESTION # 104 
Refer to the exhibit. What does this value mean when it is received in XML?
- A. It means a data field is blank.
- B. It indicates a break in a sequence.
- C. It shows the ending of the script.
- D. It indicates a value assigned by a network administrator to tag a route.
Answer: C
Explanation:
Section: Automation and Assurance
NEW QUESTION # 105
Refer to the exhibit:
Which three outcomes occur if the prefix list is added to the neighbor? (Choose three)
- A. 192.168.0.0/16 is denied
- B. 192.168 0.0/17 is denied.
- C. 192.168 0.0/17 is permitted
- D. 192.168 0.0/19 is permitted
- E. 192.168 0.0/16 is permitted
- F. 192.168 0.0/19 is denied.
Answer: A,C,D
NEW QUESTION # 106
An engineer must apply an 802.1ad-compliant configuration to a new switchport with these requirements:
- The switchport must tag all trame when it enters the port
- The switchport Is expected to provide the same level of service to
traffic from any customer VLAN
Which configuration must the engineer use?
- A. Option A
- B. Option D
- C. Option B
- D. Option C
Answer: B
Explanation:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/cether/configuration/xe-3s/asr903/16-12-1/b- ce-xe-16-12-asr900/m_ce_802_1ad_900.html
NEW QUESTION # 107
Refer to the exhibit. AN engineer is configuring segment routing on an ISP to simplify traffic engineering and management across network domains. What should the engineer do to complete the implementation of segment routing?
- A. Area authentication must be enable before segment routing will run.
- B. OSPF must be configured with wide area metrics to support segment routing.
- C. The segment-routing forwarding mpls command is required to install to install SIDs in the forwarding table.
- D. The segment routing will run without any further configuration.
Answer: A
NEW QUESTION # 108
Refer to the exhibit:
Which statement describes this configuration?
- A. Router 1 can be remotely managed by the CLI using Telnet
- B. Router 1 has a new data store to collect SNMP information, but configuration must still be done at the CLI only
- C. Router 1 has its running configuration locked so changes can be made only when the administrator issues a kill session
- D. Router 1 has a temporary data store where a copy of the running configuration can be manipulated and verified before committing the configuration
Answer: D
NEW QUESTION # 109
Refer to the exhibit:
What does this value mean when it is received in XML?
- A. It indicates a value assigned by a network administrator to tag a route
- B. It indicates a break in a sequence
- C. It shows the ending of the script
- D. It means a data fie4d is blank
Answer: D
NEW QUESTION # 110
After a possible security breach, the network administrator of an ISP must verify the times that several different users logged into the network. Which command must the administrator enter to display the login time of each user that activated a session?
- A. show netconf-yang sessions
- B. show netconf-yang sessions detail
- C. show platform software yang-management process
- D. show netconf-yang datastores
Answer: B
NEW QUESTION # 111
Refer to the exhibit.
R101 is peering with R102 and R103, and R201 is peering with R202 and R203 using iBGP Labeled Unicast address families. The OSPF area 0 border routers are in a full iBGP Labeled Unicast mesh, and VPNv4 routes are exchanged directly between PE routers R101 and R201 through iBGP Which address family-level configuration must be applied on ABR R102 on ABR R102 to support a Unified MPLS routing architecture with partitioned IGP domains?
A)
B)
C)
D)
- A. Option A
- B. Option B
- C. Option D
- D. Option C
Answer: B
NEW QUESTION # 112
Refer to the exhibit. An administrator working for large ISP must connect its two POP sites to provide internet connectivity to its customers. Which configuration must the administrator perform to establish an iBGP session between routers PE1 on POP site 1 and PE2 on POP site 2?
- A. PE2#configure terminal
PE2(config)#router bgp 65111
PE2(config-router)#address-family ipv4 unicast
PE2(config-router-af)#neighbor 172.18.10.1 activate
PE2(config-router-af)#end - B. PE1#configure terminal
PE1(config)#router bgp 65111
PE1(config-router)#no neighbor 172.19.10.10 shutdown
PE1(config-router)#end - C. PE2#configure terminal
PE2(config)#router bgp 65111
PE2(config-router)#no neighbor 172.18.10.1 shutdown
PE2(config-router)#end - D. PE1#configure terminal
PE1(config)#router bgp 65111
PE1(config-router)#address-family ipv4 unicast
PE1(config-router-af)#neighbor 172.19.10.10 activate
PE1(config-router-af)#end
Answer: B
NEW QUESTION # 113
Refer to the exhibit. Router 1 was experiencing a DDoS attack that was traced to interface gjgabitethernet0/1.
Which statement about this configuration is true?
- A. Router 1 accepts source addresses on interface gigabitethemet0/1 that are private addresses
- B. Router 1 accepts all traffic that ingresses and egresses interface gigabitethernet0/1
- C. Router 1 drops all traffic that ingresses interface gigabitethernet0/1 that has a FIB entry that exits a different interface
- D. Router 1 accepts source addresses that have a match in the FIB that indicates it is reachable through a real interface
Answer: D
Explanation:
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/4_1/nx-
os/security/configuration/guide/sec_nx-os-cfg/sec_urpf.html
NEW QUESTION # 114
......
LATEST 350-501 Exam Practice Material: https://pass4sure.examstorrent.com/350-501-exam-dumps-torrent.html